Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Do you find yourself looking for facts and techniques on Installing A Bathtub?
Installing a bath tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably hard project. If the old tub is readily accessible, the job can relocate immediately; if you need to open a wall to get rid of the old bathtub and place the brand-new tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will require a helper to move out the old tub as well as set in the new one. Ensure you have actually qualified yourself for the job as well as fit trying it. As opposed to working with a service provider to take over a halfway-completed job, it is far better to think about using one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly assist you install a new bath tub in your washroom if you have already purchased a brand-new tub as well as do not need to alter the arrangement of your previous supply of water pipes.
Your tools and also product checklist should consist of the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Making use of the two wood boards under its feet, position the tub in the called for position. The wood boards are handy in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The following objective is to make certain that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub up until the level checks out degree.
To mount taps, fit the bottom of the furthest flexible faucet port to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the water as well as examine all joints and brand-new pipework for leaks as well as tighten them if required. Fill up the tub as well as also check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as defined in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait until the tub has been used at least when as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers are in location between the tap and also the sink. Safeguard the tap in position with the maker supplied backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The former type needs to be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, creating the water to permeate the wall surface in between the bath and the tiling, resulting in complications with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily readily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
As a person who reads on Tools You Need to Install a New Bathtub , I imagined sharing that information was sensible. Are you aware of another individual who is fascinated by the niche? Do not hesitate to promote it. Thanks a lot for your time. Please pay a visit to our website back soon.
Visit Report this page